![]() Only their own units from the pfSense Shop they are knowing well, but anyway, if you buy a SG-xxxx Why? The pfsense team is not able to see or expect the hardware we all are using everywhere! Unset - Click this button to return the value of the selected attribute to its default value.–- I was pretty frustrated getting TRIM enabled in 2.2.4 If your part appears faceted, set the tolerance to a lower value. Tolerance - This attribute controls how accurately the toolpath follows the surface. Target horsepower - This is the ideal power for the specified width/depth of cut and feed rate on the specified stock material type. 100 stops one tool radius short of the stock curve. Overcut % specifies what percentage of the tool approaches or passes beyond the stock boundary.Ġ puts the centerline of the tool on the stock curve.ġ00 overcuts the region by a tool radius. Use stock dimensions is selected on the feature's In the boss case this attribute applies only to how the toolpaths behave around the stock boundary.įor other 3D surface milling features, use the cut allowance feature described on the features cut with projection milling technique that do not have an explicit boundary curve.spiral toolpaths designated as a boss on the stock page.This example shows a feature cut with a value of Specify the value as a percentage of tool diameter. Minimum rapid distance applies to 2.5D milling. Moves smaller than this distance use a feed move. ![]() rapid distance % - Enter the minimum distance, as a percentage of the tool diameter, that the tool can use a rapid move for. Leave allowance is applied to axial and radial material. Leave allowance is applied to radial (XY) material only. Leave axial allowance - Enter the amount of axial (Z) material to leave on a feature after the Finish pass. You can enter a negative number, up to minus the tool radius, to allow for shrinkage or spark gaps, and the part is machined into the part surfaces by the negative amount specified. Leave allowance - Enter the amount of material to leave after a finish pass. Initial C-axis position of the part in the machine at the start of the operation. It can also result in less-efficient retract moves if the part is an irregular shape. This can result in a Z value for indexing that is outside the valid range for the machine. Z index clearance is a clearance distance above the stock bounding cylinder. Z index clearance value is used for the index retract move. Note: If you do not enter a coordinate, the Index Z coordinate - Optionally enter the absolute Z coordinate to use for the index retract move. Index Y coordinate - Optionally enter the absolute Y coordinate to use for the index retract move. Index X coordinate - Optionally enter the absolute X coordinate to use for the index retract move. The toolpath is clipped where the shank moves within this distance of a part surface or check surface. Shank clearance - Enter the clearance distance for the tool shank.The toolpath is clipped where the tool holder moves within this distance of a part surface or check surface. Holder clearance - Enter the clearance distance for the tool holder.When enabled, these options are displayed: Holder collision clipping on the feature's Holder Collision Clipping - Clips the toolpath where the holder or shank collides with a part surface, check surface or unmachined stock. You can enter a positive orĭirection - Click this button to open the If you leaveĬheck axial allowance blank, the value forĬheck allowance is applied to axial and radial check surfaces. If you enter a value forĬheck allowance is applied to radial (XY) check surfaces only. You can enter a positive orĬheck axial allowance - Enter the amount of axial (Z) material to leave on a check surface. If left blank for a roughing pass, theįinish allowance value is used. Positive numbers offset the toolpath towards the tool holder, negative numbers away.Ĭheck allowance - Enter the minimum distance that you want to leave around check surface(s). Preferred orientation of the primary rotary axis option.įeatureCAM to select the orientation that best fits within the axis limits set in the MD file.Īxial offset - This attribute offsets the lowest position of the toolpath along the tool axis. Use Post Preference - Uses the position ( Positive or.Alternate - The alternative orientation to the default.Alternate orientation option for accessing a face.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |